亚洲无码特级一级片_看国产精品美女黄片_av不卡无码免费播放_国产精品原巨作AV无遮挡

86-15237383444
EXPLAIN

Description And Aufbau Principle Of G263 Series Disc Loom

Release:hnfzpj Click:17805

This article focuses on the description and Aufbau principle of G263 series disc Loom. We use drawings such as the principle of bobbin changing and picking to give a detailed and comprehensive introduction to the automatic bobbin changing structure, so that the textile industry can be fully familiar with the description of Loom, the principle of Loom, the parameters of Loom, and the principle of disc looms, and meet the requirements of improving the innovative production and maintenance technology of Loom and updating the equipment of Loom in China.

Description of the process of automatic filament changing on the Loom

Introduction:

G263 (Z) disc loom is a cotton loom suitable for weaving pure cotton and blended cotton yarn. It is suitable for weaving fabrics with a weft density of 40-80 pieces/inch. There are mainly three types of loom door widths: G263-1250mm, G263Z-1350mm, and G263Z-1500mm. The machine speed is 185-200r/min, and the warp disc adopts φ 550mm or φ 600mm, equipped with the same motor as the 1511 and 1515 models -0.8KW.

(1) Shuttle size: 390mmX48mm X35mm (total shuttle length X shuttle bottom width X shuttle wall height)

(2) Size of weft tube with iron hoop: 190mm long, outer diameter of weft tube hoop 27mm

(3) Reed size: 1302mm long X 120mm high, 1404mmX120mm, 1578mm X120mm (calculated according to the door width of the Loom).

Hand drawn drawings of G263 automatic filament changing loom

When the G263 disc Loom works normally, it operates smoothly, the three spindles rotate flexibly, the axial clearance is less than 0.4mm, the crankshaft gear and the pedal shaft gear are well matched, and the tooth side clearance is less than 1.5mm. When the clutch starts working, the fully opened shuttle opening should be clear, and there should be no abnormal clamping phenomenon when the shuttle enters and exits the shuttle track.

(1) The reed seat of the disc loom is located at the lower warp surface of the rear center shed, which is about 1mm away from the plane of the shuttle board or flat, and cannot cause friction with the shuttle board. When the reed seat is in the rear center, a gap of 15-20mm should be maintained between the front heald frame and the reed cap.

(2) The surface of the tread plate has good contact with the surface of the tread rotor, and the parallelism of the contact surface is 0.2mm.

(3) The surface contact between the shuttle rotor and the shuttle nose is good, with a parallelism of 0.1mm on the contact surface. The angle between the shuttle box bottom plate, the shuttle box back plate, and the shuttle box front plate is 86.5 °.

(4) Shuttle box width: the inner side is the width of the shuttle+3mm, and the outer side is the width of the shuttle+1.6mm; Shuttle box height: The inner side is the shuttle height+4mm, and the outer side is the shuttle height+2mm.

(5) The shuttle surface at the junction of the shuttle box bottom plate and the shuttle board must be flush, with a horizontal shuttle board arc (concave) of 1.5mm and a steel reed (convex) of 1.5mm.

(6) The relative displacement of the coiling hook is three teeth and a half, the gap between the side support box and the steel reed is 1.6mm, and the distance between the side support cover edge and the shuttle plate surface is 22mm (G263) and 32mm (G263Z).

The Principle of Automatic Shuttle Changing Loom Picking

Technical requirements for fiber exchange system:

(1) The ratchet sleeve rotates flexibly, and the three pawls have good contact with the ratchet. When the handle is pulled and released again, the ratchet can rotate one tooth on its own.

(2) The positions of the disc, keyboard, and yarn guide are aligned with each other, and the guide iron plane is flush with or retracted by 0.5mm from the concave surface of the disc

(3) The gap between the curved surface of the replacement hammer and the pipe clamp: 3mm when lifting up and 1mm when pressing down.

Process Diagram of Fiber Replacement on G263Z Disc Loom

The above is the description of the G263 Loom and the principle of the G263Z Loom. The attached picture is the Aufbau principle diagram of the disc Loom. The different design methods of the disc Loom are complementary to the types of fabric changing and shuttle changing looms, which are based on reducing the failure rate and improving the production efficiency.

FriendLink: BaiDu  Ecer  Xinda Textile  Ec21  Ecplaza  Chinatexnet  Every China  
Copyright © 2016 Xinxiang City Xinda Textile Machinery Parts Co. Ltd 【MANAGE】
ADDRESS:5F West, Unit 53A, Zone A, Huicheng Port Bay, Huixian City, Henan Province,China CONTACT:Mr Yang MOBILE:86-15237383444
TEL:+86-0373-6235050 FAX:+86-0373-6235050 E-MAIL:309816745@qq.com
WEB:http://www.fcbergquistphotos.com
SERVICE
CUSTOMER ONE:
點擊這里
CUSTOMER TWO:
點擊這里
TEL:0373-6235050